了解丹富莱 深圳丹富莱科技有限公司公司成立于2007年,是专业从事电机驱动、自动化系统研发、生产和销售的专业制造商。

  • 邮 箱: 1596333050@qq.com

  • 全国服务热线: 133-2686-1162

  • 4新闻中心
    您的位置:首页  ->  新闻中心  -> 公司动态

    DFL3000M恒压供水变频器的接线和参数设置操作

    文章出处:深圳市丹富莱科技有限公司 责任编辑:深圳市丹富莱科技有限公司 发表时间:2021-05-24
      

    DFL3000M系列是一款可以安装在电机接线盒上的背负式恒压供水变频器,它可分为单相输入单相输出恒压供水变频器,型号为DFL3000M-HYGS1,专用于单相220v的水泵;单相输入三相输出的,型号为DFL3000M-HYGS3,用于三相220v的水泵。其外形如下:

    恒压供水变频器

    3000M系列于电机和压力传感器的接线图如下所示,220v的电源连接AC,AC两个端子,单相的水泵连接U,V两个端子:


    压力变送器于变频器的连接如下图,压力变送器的1,2两个点分别连接V/I,12V.

    接好线之后,通上电源,一般变频器上会显示两个压力,左边为设置压力,右边为管道的压力。在一拿到变频器,如果没有跟销售人员说明所用是何种压力传感器,有可能还需要设置你相对应的压力传感器,如视频所示

    首先,先进入系统,每一台变频器为了不误操作都有一个密码,为0168。先按左上角的编程键两次,当显示.0000时,按上下的方向,输入0168,然后按左下方的保存确认键,这样就成功进入系统。

    进入系统后显示参数pr130,转是设置压力传感器量程的参数号,比如我们用的压力传感器的最大值为1.0mpa,可以按以下视频操作。在显示pr130时,按左下角的功能保存确认键,进入该参数设置,设置为d01.00.此处数值单位为mpa。


    一般只是需要设置量程就可以,为了用户能够更简单的使用3000M变频器,变频器出厂时设置了一次恢复模式,比如你根据使用压力传感器的输出信号,比如0-5vdc,0.5-4.5vdc,4-20ma,三个选择。与下表pr068 中的d0010,d0017,d0018相对应

    Parameter No.

    Function description

    Setting rang

    Factory default

    Pr068

    Parameter lock/restore settings (return to the factory default needs to power-off completely and repower-on)

    The factory default is displayed as five flashing “8”, and any key shall be pressed at this time.

    (it takes 5s-8s to return to the factory default.)

    dr0000: All parameters can be readable and writable

    d0001: All parameters can be readable but not writable

    d0000-

    d0019

    d0000

    220V model

    d0010: Restore to single-phase water pump 0-5V factory parameters

    d0017: Restore to single-phase water pump 4-20mA factory parameter

    d0018: Restore to single-phase pump 0.5-4.5V factory parameters


    Pr000

    Main frequency source selection

    d0000- d0004

    d0001

    Note: 0: frequency can be modified by the up and down keys on the panel.

    1: 0-5V analog quantity input (common for water supply)

    2: Control the main frequency through RS485

    3: 4-20mA input (common for water supply)

    Pr001

    Operation instruction source

    d0000- d0004

    d0000

          0: panel key of start and stop

          1: external terminal of start and stop

    Pr034

    X4 multi-function terminal function selection

    d0001- d0022

    d0019

          19: enable PID function

    Pr035-

    Pr123

    ******

    *****

    *****

    Pr124

    Password setting of the frequency converter

    d0000-

    d9999

    0168

    The parameter modification interface can not be entered until the correct password is input.

    Pr126

    Time (unit: minute) can be automatically reset after the water shortage.

    d0000-

    d9999

    d0030

    Pr127

    Automatic reset function for water shortage protection (for water shortages only)

    d0000-

    d0001

    d0000

    0: it is forbidden to start the automatic reset

    1: enable automatic reset and start the frequency converter

    Pr128

     The corresponding voltage of the pressure gauge 0MPa

    d00.00- d10.00V

    d00.15

    0.15: 0-5V compensation value

    0.5: 0.5-4.5V compensation value

    1.0: 4-20mA compensation value

    Pr129

    The corresponding voltage when the pressure gauge is in full scale (it can be used to calibrate pressure value)     

    d00.00- d10.00V

    d05.00

    4.50: 0.5-4.5V pressure sensor corresponding value

    5.00: Remote transmission pressure gauge/4-20mA pressure transmitter corresponding value

    Pr130

    Scale setting of the remote transmission pressure gauge/ pressure transmitter (unit: Mpa)

    d00.00- d10.00

    d00.60

    Pr131

    PID target value (Mpa)

    d00.01- d01.00 Mpa

    d00.25

    Setting pressure value SV can be modified by directly pressing the up and down keys in the pressure display state; Note: 0.1Mpa=1 kilogram pressure

    Pr132

    Proportionality constant (P)

    d0000- d0999

    d0055

    Pr133

    Integration time (I)

    d0000- d0999

    d0009

    Pr134

    Differential time (I)

    d0000-

    d0100

    d0000

    Pr135

    PID target source selection

    d0000-

    d0001

    d0000

    d0000: determined by Pr0131

    d0001: determined by external analog quantity (0-10V)

    Pr136

    PID upper limit (%)

    d0000- d0100

    d0100

    100% of the corresponding frequency is 50HZ.

    Pr137

    PID lower limit (%)

    d0000- d0100

    d0040

    40% of the corresponding frequency is 20HZ.

    Pr138

    Shutdown pressure level (%)

    d0000- d0200

    d0090

    Note: shutdown pressure= setting pressure*Pr138

    Pr139

    Continuous time (seconds) of shutdown pressure level

    d000.0-

    d999.9s

    d030.0

    Note: within the setting time, if the actual pressure has always been greater than or equal to the shutdown pressure level, the frequency converter will start to decrease frequency to the sleep frequency;

    Pr140

    Wake-up level (%) (Wake-up pressure = setting pressure* Pr140)

    0100%

    d0080

    Note: When the actual pipeline pressure is less than the wake-up pressure, the frequency converter starts automatically;

    Pr 141

    Sleep frequency

    d000.1—d060.0Hz

    d025.0

    Note: If the frequency converter runs at the frequency within the time set by Pr142, and the actual pipeline pressure has always greater than or equal to the shutdown pressure, the frequency converter will stop automatically;

    Pr142

    Continuous time (s) of sleep frequency

    d000.1—d999.9s

    d30.00

    Pr143

    High-speed operation time (s) in frequency conversion of 50HZ:

    d0001 —d9999s

    d0060

    After the time is up, the frequency conversion stops outputting. After the interlocking time expires, the power frequency relay shall be turned on to switch to the power frequency state.

    Pr144

    Interlocking time between power frequency and frequency conversion (s)

    d000.1—d600.0s

    d002.0

    Pr145

    Operation time of the power frequency (s)

    d0060

    d0060

    After the power frequency operation time is up, if the actual pressure is not greater than 110% of the setting pressure, it will always run in the power frequency state.

    Pr146

    Power frequency state

    d0000-

    d0001

    d0000

    Note: d0000: there is no power frequency contactor

    d0001: There is a power frequency contactor

    Pr147

    Pipe-burst pressure/pressure is too low (MPa)

    d00.00—d10.00MPa

    d00.05

    Note: In the setting time of Pr149, when the actual pipeline pressure is less than the setting value, the frequency converter will automatically stop and the 220V model machine will display Er.012 and the 380V model machine Er.014.

    Pr148

    Pipe-burst pressure alarm is delayed.

    d0000 —d0600 s

    d0060

    Note: if the frequency converter detects that the water pressure is lower than the pipe-burst pressure over the setting time, it will report fault and shutdown.

    Pr149

    Energy saving coefficient (decrease increment)

    d0000-

    d0100

    d0004

    Note:

    Pr150

    Standby (open the flow switch)

    d0000-

    d0001

    d0000

    Note: 0: the manual and automatic switch shall be determined by X4 terminal signal.

    1: Panel manual/automatic keys can also be switched.

    Pr151

    Flow threshold (flow frequency HZ)

    d0000-

    d2000

    d0040

    When the flowmeter is enabled, if the detected actual flow is less than the setting value, the frequency converter will stop automatically;

    Pr155

    Timer 1 (No.1 pump running time) minutes

    d0000-

    d9999

    d0030

    Pr156

    Timer 2 (No.2 pump running time) minutes

    d0000-

    d9999

    d0030

    Pr157-

    Pr164

    Standby

    d0000-

    d9999

    d0000

    Pr165

    Dual pumps alternation function can be used with Timer 1 and Timer 2.

    d0000-

    d0001

    d0000

    Pr166

    Standby

    d0000-

    d0001

    d0000

    ​以上是3000M系列的接线和参数设置操作,如有其他不明白,请与丹富莱公司联系

    /*浮动QQ*/